特别注意：
我们发现不同开源遥控(或多协议高频模块)，由于硬件制造差异(甚至批次差异)，造成情况各不相同因此，150V3系列产品能够在Boxer遥控器上实现，但无法在TX16S上完美实现，如果是TX16S用户，遥控器无法充分发挥飞机性能，会牺牲10%左右。其他开源遥控器可能存在其他差异情况，需要用户自己根据自己情况进行行程设置。
设置基本原则：
1. 遥控器的通道顺序要设置成和飞机匹配，成功的控制关系是：
遥控器Thr(油门)控制飞机马达转速
遥控器Rud（航向）控制飞机自旋方向
遥控器Ele(俯仰)控制飞机前进后退
遥控器Ali(副翼/侧滚)控制飞机左右移动
2. 第5和6通道开关采用2档开关，如果没有2档，采用3档的，需要在遥控器里把3档开关定义成2档开关
3. 从第7通道开始到第18通道，输出值全部设置为1500，可在OUTPUT（输出）页面设置
4. 需设置合适行程：
对于【Mini雏鹰II】和【海鸥】而言：
TX16S行程设置参考：1-6通道输出行程为：-100% - +101%
Boxer行程设置参考： 1-4通道输出行程为：-100% - +100%, 5-6通道 -105% - +105%
对于150V3/150BL/150EC：
TX16S行程设置参考：1-6通道输出行程为：-105% - +105%，
Boxer行程设置参考： 1-4通道输出行程为：-100% - +100%, 5-6通道 -105% - +105%
其他遥控器，原则上一样，实现不了的，请把遥控器寄ESKY售后，让帮忙适配。
===========================================================================================
How to Set Up ESKY Products with the EdgeTX System and a Multi-Protocol 4in1 RF Module
Published: 2024-06-07 | Source: ESKY Team
Important Note:
We have found that different open-source transmitters (or multi-protocol RF modules) behave differently due to hardware manufacturing variations (even batch-to-batch differences). Therefore, the 150V3 series can be fully implemented on the RadioMaster Boxer, but cannot be perfectly implemented on the TX16S. If you are a TX16S user, the transmitter will not be able to fully unleash the aircraft's performance, with roughly a 10% compromise. Other open-source transmitters may have their own differences, and users should set up the channel travels according to their specific situation.
Basic Setup Principles:
1. The transmitter channel order must be set to match the aircraft. A correct control mapping is:
- Transmitter Thr (Throttle) → controls the aircraft's motor speed
- Transmitter Rud (Rudder) → controls the aircraft's spin/yaw direction
- Transmitter Ele (Elevator) → controls the aircraft's forward/backward movement
- Transmitter Ali (Aileron/Roll) → controls the aircraft's left/right movement
2. Channels 5 and 6 should be assigned to 2-position switches. If no 2-position switch is available, a 3-position switch may be used, but it must be defined as a 2-position switch in the transmitter settings.
3. From Channel 7 to Channel 18, set all output values to 1500. This can be done on the OUTPUT page.
4. Proper channel travel must be set:
For the Mini Eagle II (Mini雏鹰II) and Seagull (海鸥):
- TX16S travel reference: Channels 1–6 output travel: -100% to +101%
- Boxer travel reference: Channels 1–4 output travel: -100% to +100%; Channels 5–6: -105% to +105%
For the 150V3 / 150BL / 150EC:
- TX16S travel reference: Channels 1–6 output travel: -105% to +105%
- Boxer travel reference: Channels 1–4 output travel: -100% to +100%; Channels 5–6: -105% to +105%
For other transmitters: The principle is the same. If the setup cannot be achieved on your transmitter, please send the transmitter to ESKY after-sales service so we can adapt it for you.
